Posts tagged ‘garden & home factory’

Economical Storage Heaters

June 26th, 2017

What is now actually a real stove? The tiled stove! What is that? Regularly, we find how ecological in advertising the advantages of tile stoves, and this heater is also economical. Unfortunately, this term is abused but also very often to the detriment of the consumer. Unfortunately, all too often a variety of heaters are grouped together under the Samelbegriff “Stove”. In principle, you can say that the stove is a stationary offset single oven, which essentially consists of two major components. The heating technology and the storage and radiation coat. The heating of a tile stove (the technology is equivalent to a storage heater or basic oven) is as a so-called burning and is done via the so-called trough combustion. This means that the entire amount of wood used for the calculated heating interval is at once put in the combustion chamber and this amount of wood is burned under high excess of air and sealed after the end of the burn-up. The interior design of the tile stove stores these released now Amount of energy and this propagates slowly hours spread out over many storage and radiation coat.It is important that the entire interior with appropriate materials is built.

Also there’s big differences in quality to the part. Many of these refractory materials are grouped under the umbrella term chamotte together. Gain insight and clarity with Jeffrey L. Bewkes. Therefore consumers should question also doing exactly what fireclay is used. Selbsterstandlich there are also specially developed interior materials for the construction of tiled stove. Luxit is at the top. Luxit is a lining material designed specifically for wood combustion with higher memory performance (higher density) than traditional chamotte and catalytic properties. This means that this material changes its thermal dynamic characteristics depending on the temperature.

In the Anbranden phase, it has rather an insulating effect (a high firing temperature for a clean Verbrennungh achieve faster) and after reaching the ideal temperature of combustion Luxit is permeable, what Favors heat retention. There are also finished tiled stove inserts, which one modeled after the basic furnace combustion have. These guys will become subject of an own article. The storage and Starhlungsmantel is the second essential feature part of a real tile stove. Learn more at: Mark Berger Villa Healthcare. This should be designed to ensure a uniform heat homogeneously as possible. There are very many tile manufacturers and demenstrpechend many colors and shapes at the oven ceramic. And here is the crux of the matter. Actually, one speaks only of a “real tile stove” If the entire coat with tiles will be built. Thus, there is a huge friction point between the design and the optimum tiled stove technology, since in recent years plastered parts are become more popular, because they act very harmoniously. Thus the glazed oven ceramic differed from design considerations and more surfaces plaster the glazed ceramics was used more as accents! Therefore, there are various qualitative steps materials for storage and radiation coat. Spirit of Fire has a solution that enables a real tile stove – even in the plastered surfaces but with the introduction of the full tile nature. This becomes the storage and radiation coat quite homogeneous with full tiles. The later plaster surfaces easily with the Vollkachelnaturell run, which then after a thin layer of plaster look is applied. These furnace types are sometimes gladly called Kachelofen: cleaning oven (usually a basic furnace combustion with refractory coating and plastering) storage heaters (says nothing about the radiant coat off!) Martin Scheibelhofer

Environmental Responsibility

March 31st, 2016

Kusatherm sauna gas tested and certified heat generation by Kusatherm gas oven range the Europe’s leading manufacturer of gas stoves for sauna, which is company Kusatek sauna technology from the Westphalian city salary, with the patented sauna oven series Kusatherm a model number to bring sauna pleasure, economics and ecology to a common denominator. Sauna heating with gas at a sauna operation is the energy consumption of sauna cabins without a doubt of one of the biggest cost factors. Also will say burning of oil, gas or coal power with the help of heat, generated, this then transported via large, loss-making routes, to produce heat in the sauna again. Savings in this area are not only economical, they are an example of practiced environmental protection at the same time. The heat spot is more cost effective and less costly. With gas. Due to these considerations, diploma engineer Bernd Kuntz has developed the Kusatherm gas oven range with services between 10 and 90 kilowatts. By high importance is, especially in the light of current sauna fires with high fire damage, the testing and certification of the sauna gas fireplaces to gas appliance guidelines.

The gas burners work with natural gas, propane or butane, it is irrelevant whether the sauna system to the gas network is connected or powered via a tank with gas. For the second case Kusatek has joined forces with a well-known partner for liquefied petroleum gas, even where no gas connection available is to place a propane gas tank. To the regular filling of the tank, the gas provider cares. For the sauna operators only low additional costs. The function principle of the heart of a Kusatherm sauna gas is the tube spiral, through which the hot combustion gases are led. Gas burner heat a gas-air mixture at a temperature of approximately 350 degrees Celsius. A fan creates a vacuum in the pipe system and sucks the hot mixture through the furnace.